Certificate III in Electrical Fitting - UEE33020
Charles Darwin University
Type of institution: University/Higher Education Institution
Level: Vocational Education and Training (VET)
CRICOS: 00300K
This qualification provides competencies to manufacture, fit, assemble, erect, operate, test, fault find, alter and repair electrical equipment and includes electrical wiring work only if that work is associated with assembling, maintaining, terminating or altering the wiring between electrical components within a plant or machinery. An electrical fitter is not authorised to install any electrical wiring systems within an electrical installation as prescribed by definitions contained in AS/NZS 3000 Electrical installations (known as the Australian/New Zealand Wiring Rules)..Electrical equipment means any appliance, article, accessory, wire, fitting, cable, conduit or apparatus that generates, uses, conveys or controls (or that is intended to generate, use, convey or control) electricity above extra-low voltage (ELV). The skills and knowledge described in this qualification may require a licence or permit to practice in the workplace where work is carried out on electrical installations which are designed to operate at voltages greater than 50 volt (V) alternating current (a.c.) or 120 V direct current (d.c.).Competency development activities in this qualification may be subject to regulations directly related to licensing. Where a licence or permit to practice is not held, a relevant contract of training through an Australian Apprenticeship, may be required.Licensing, legislative and regulatory requirements that apply to this qualification can vary between states and territories. Some jurisdictions require that the qualification is completed as an apprenticeship to obtain an Electrical Occupational License. Relevant information must be sourced prior to commencing the qualification. Where required for Licencing, the certification documentation issued must indicate if the qualification was completed as an apprenticeship or Trades Recognition Australia (TRA) pathway.
Subjects
- Solve problems in magnetic and electromagnetic devices
- Align and install traction lift equipment
- Assemble, enter and verify operating instructions in microprocessor equipped devices
- Arrange circuits, control and protection for electrical installations
- Supervise repair and overhaul of explosion-protected equipment type pressurised (Ex p)
- Develop, enter and verify discrete control programs for programmable controllers
- Install explosion-protected equipment and associated apparatus and wiring systems
- Install instrumentation and control apparatus and associated equipment
- Provide cardiopulmonary resuscitation
- Troubleshoot single phase input d.c power supplies
- Perform low voltage field switching operation to a given schedule
- Supervise repair and overhaul of explosion-protected equipment type flameproof (Ex d)
- Conduct mechanical tests on electrical machines and components
- Install instrumentation and control cabling and tubing
- Conduct electrical tests on LV electrical machines
- Assemble, mount and connect control gear and switchgear
- Recover and charge refrigerants
- Solve problems in temperature measurement components and systems
- Perform power system substation switching operation to a given schedule
- Sample, test, filter and reinstate insulating oil
- Supervise repair and overhaul of explosion-protected rotating machines
- Develop and connect electrical control circuits
- Locate and rectify faults in low voltage (LV) electrical equipment using set procedures
- Establish the basic operating conditions of vapour compression systems
- Participate in electrical work and competency development activities
- Overhaul and repair major switchgear and control gear
- Supervise repair and overhaul of explosion-protected equipment type intrinsically safe (Ex i)
- Install and maintain cabling for multiple access to telecommunication services
- Diagnose and rectify faults in traction lift systems
- Disconnect - reconnect electrical equipment connected to low voltage (LV) installation wiring
- Rewind three phase low voltage induction machines
- Maintain capacitor bank equipment for voltage regulation
- Disconnect-reconnect 3.3 kV electric propulsion components of self-propelled earth moving vehicles
- Test copper rail signalling cables
- Isolate, test and troubleshoot low voltage electrical circuits
- Apply work health and safety regulations, codes and practices in the workplace
- Evaluate and modify low voltage socket outlets circuits
- Solve problems in single path circuits
- Maintain equipment associated with hazardous areas
- Find and rectify faults in single phase motors and associated controls
- Supervise repair and overhaul of explosion-protected equipment type increased safety (Ex e)
- Find and rectify faults in appliance control systems and devices
- Apply environmentally and sustainable procedures in the energy sector
- Test and connect transformers
- Service small electrical appliances and power tools
- Use drawings, diagrams, schedules, standards, codes and specifications
- Wind electrical coils
- Document and apply measures to control WHS risks associated with electrotechnology work
- Solve problems in pressure measurement components and systems
- Repairs basic electronic apparatus faults by replacement of components
- Use and maintain the integrity of a portable gas detection device
- Mount and wire control panel equipment
- Disconnect-reconnect explosion-protected appliances and control devices connected to LV installation
- Solve problems in energy supply network equipment
- Repair rail signalling power and control cables
- Solve problems in low voltage a.c. circuits
- Safely handle refrigerants and lubricants
- Service electrical heating appliances
- Carry out basic repairs to electrical components and equipment
- Supply effective and efficient lighting products for domestic and small commercial applications
- Install refrigerant pipe work, flow controls and accessories
- Maintain operation of electrical mining equipment and systems
- Provide advice on the application of energy efficient lighting for ambient and aesthetic effect
- Service clothes washing machines and dryers
- Identify, shut down and restart systems with alternate supplies
- Use instrumentation drawings, specifications, standards and equipment manuals
- Terminate cables, cords and accessories for low voltage circuits
- Place and connect electrical coils
- Repair and maintain mechanical components of electrical machines
- Provide advice on effective and energy efficient lighting products
- Fabricate, assemble and dismantle utilities industry components
- Service refrigeration appliances
- Test and connect alternating current (a.c.) rotating machines
- Fabricate and assemble bus bars
- Conduct compliance and functional verification of electrical apparatus and existing circuits
- Perform HV field switching operation to a given schedule
- Rewind LV direct current machines
- Evaluate and modify low voltage lighting circuits, equipment and controls
- Find and repair faults in LV d.c. electrical apparatus and circuits
- Assemble and connect telecommunication frames and cabinets
- Solve problems in direct current (d.c.) machines
- Solve problems in flow measurement components and systems
- Evaluate and modify low voltage heating equipment and controls
- Attach HV flexible cables and plugs
- Solve problems in density/level measurement components and systems
- Fix and secure electrotechnology equipment
- Prepare and connect refrigerant tubing and fittings
- Maintain operation of electrical marine equipment and systems
- Install and start up single head split air conditioning and water heating heat pump systems
- Determine the explosion-protection requirements to meet a specified classified hazardous area
- Assemble and wire internal electrical rail signalling equipment
- Use engineering applications software on personal computers
- Establish the basic operating conditions of air conditioning systems
- Install, modify and verify coaxial and structured communication copper cabling
- Enter a classified hazardous area to undertake work related to electrical equipment
- Solve problems in energy supply network protection equipment and systems
- Supervise repair and overhaul of explosion-protected equipment type Group III ('t')
- Find and rectify faults in three phase motors and associated controls
- Solve problems in multiple path circuits
- Maintain and service traction lift systems and equipment
- Rewind single phase machines
Study information
| Campus | Fees | Entry | Mid year intake | Attendance |
|---|---|---|---|---|
| Alice Springs | Domestic: $15,450 | No |
| |
| Casuarina | Domestic: $15,450 | No |
|
-copy.webp){kind=logo}
